No Products in the Cart
Inca Trail Terpenes does not sell any products with THC. Check with your state and local laws for the legality of making these products. Care should be taken to ensure safety at all times. Please wear gloves and eye protection and have proper ventilation. Our products are extremely concentrated. Review our SDS for more information. Not for sale to persons under the age of 18 years old.
Mixing Instructions
Terpenes are aromatic compounds that add flavor and effect. These compounds can be added to various products to create synergy according to your personal preference.
Here are the most common methods of mixing our terpenes. Please remember that these are just starting points. More may be required. You can always add more, but you can’t take away once added, so start small.
1 drop with our glass dropper is approximately 0.02 grams. Higher amounts should be weighed on a quality scale for accuracy.
CARTRIDGES
Making cartridges can be very technical and will require trial and error to find your perfect balance. The outcome is highly dependent on your hardware, quality of starting product, and your goals.
Plastic is limited to adding a maximum of 6% terpenes as plastic can have a negative reaction. Poor quality plastic can give a burned taste!
Plastic cartridges will require another product to cut it.
Making Plastic Cartridges with a Non-Winterized Product: Shatter, Wax, Rosin, etc
This is not the best way to make cartridges but it can be done successfully. The cleaner the wax, the better. But this method can be finnicky due to the nature of the product.
Depending on the product amount and the wattage of the microwave this should take 2-5 minutes approximately.
*Avoid water baths, which can lead to glass breakage and contamination.
Making Plastic Cartridges with De-Waxed Products: Distillate/Clear
Depending on the product amount and the wattage of the microwave this should take 2-5 minutes approximately.
*Avoid water baths, which can lead to glass breakage and contamination.
Making Glass Cartridges with a Non-Winterized Product: Shatter, Wax, Rosin, etc
Follow the same instructions as above but you can use a higher percentage of terpenes if desired, up to 8%.
Non-wick cartridges can be used after 1 hour to allow the product to make full contact with the atomizer.
Making Glass Cartridges with De-Waxed Products: Distillate/Clear
Follow the same instructions as above but you can use a higher percentage of terpenes if desired, 8-20%. 10% is usually the sweet spot although we know of companies who use 20% depending on the hardware.
Cartridges and color change – Remember, distillate will naturally oxidize and certain terpenes may affect the color.
Uncut
For people who want the highest quality product with distillate, simply add 10% terpenes after heating your product and mix thoroughly. You do not need to cut it with Liquify.
ISOLATE (UNFLAVORED)
Starting point: 2% by weight.
Example: 1 gram of product, add 0.02 grams (Approximately 1 drop with our provided glass dropper)
SHATTER, WAX, ROSIN, ETC.
Starting point: 2% by weight.
Example: 1 gram of product, add 0.02 grams (Approximately 1 drop with our provided glass dropper)
FLOWERS/BUDS
Starting point: 2% by weight.
Example: 1 gram of product, add 0.02 grams (Approximately 1 drop with our provided glass dropper)
Alternate use: Spray buds using a pump sprayer (Always use glass, or an approved HDPE plastic sprayer to avoid undesirable reactions.)
Example: Use a light even spray that does not fully saturate the flower, gently toss in an enclosed container to cure.
LOTIONS, COSMETICS, SCRATCH AND SNIFF STICKERS
Starting point: 5% terpenes by weight.
Example: 1 ounce of lotion (28 grams), add 1.4 grams of terpenes
We recommend using a scale that goes down to at least 0.00.
SPARKLING WATER, CHAMPAGNE, BEVERAGES, ETC.
Starting point: 4-6 drops per Liter
Example: 1 glass of champagne, add 1 drop of your favorite terpene
EDIBLES
Starting point: Depending on the edible, start with .5% by weight and adjust accordingly. We don’t want the terpene to overpower the edible.
Example: Hard candy batch weighing 14 grams, add 0.07 grams of terpenes.